The Light Efficacy of HPWINNER Whole Lamp Reaches 180lm/W with Competitive Price.
HPWINNER 180 lm/W LED street lamp adopts modularization honeycomb heat effect， and the whole structure of the cooling technology to meet the lower work the LED junction temperature, using more than 93% of the integration of high transmittance lens group, combined with flip-chip technology and the Inventronics who hold high efficiency drive power supply, to achieve the higher electro-optic conversion efficiency and a low optical loss, so as to achieve the 180 lm/W of the whole lighting effect.
HPWINNER 180lm/W LED Street Lights have the advantages as below:
Heat dissipation of Honeycomb Briquette effect
It simulates and adopts the burning principle of honeycomb briquette; solid briquette burns slowly and inadequately due to the insulation of its center from outer air, the honeycomb structure enables coal to burn fast due to air convection, which is called the Honeycomb Effect. Similarly, it is available to transform the original whole block of radiator into various modules, as well as to enable air to convect and fully pass through the gaps between modules by utilizing the honeycomb effect, thus to dissipate the heat rapidly and reduce temperature by around 20 ℃.
Heat dissipation of the whole structure
It is available to make clever use of the module bracket that only plays a supporting role, and to transform it to a "heat-conductive bracket" that is capable of conducting the module's heat to the lamp shell as a structural part, thus to promote the cooling effect of radiator of cooling module, the design aims to fully utilize the surface area of structural parts to transfer heat to air.
It adopts the special structural design to achieve the manual disassembly and installation of lighting components (mainly module and power supply), considering that the high-power lights are generally installed in high operating space, it’s very necessary for the operators to take along as few tools as possible for their convenience and safety.
Double-coupling IP68 protection
It adopts the screw-free structure to avoid the penetration of water vapor through the screw hole, and its double silicon-rubber rings insulate LED chip from the outside environment completely, thus to protect inner LED chip and PCB from any erosion caused by water vapor or other noxious gas.
Dye Penetrant Analysis of the couplings. Besides tests under normal water, the Dye penetrant is applied. Put the module into 100 degree red boiling water for 30 minutes and then suddenly put it into the normal water to test whether the red ink permeates the couplings of the modules. Such tests will be repeated for 6 times in 3 hours. Thus, the results will show what IP rate it will reach. HPWINNER’s modules have got a perfect IP68.
"Ultra Robust" module technology
Each LED is equipped with bypass protection, to protect single-circuit structure of the full connection series, even open or short circuit fault can't affect current and voltage distribution of other LEDs, and the other LEDs can work under the normal operating mode without any influence, thus extending the life cycle of the whole module.
Multi-circuit constant-current driver power
Independent multi-circuit constant-current output, each circuit is independently controlled; any failure in single circuit will not affect the normal working of other circuits. But it's different in traditional single-circuit external LED driver; single-circuit power supply must be matched with LED electrical structure in series and parallel. Certainly, the differences among LEDs’ VF values, unavoidably existing in series and parallel structure, may cause an uneven current distribution, resulting in severe decadency in part of LED units. If a single LED unit is damaged, the current distribution is more uneven in entire series and parallel structure, which sharply increases the damage rate of other LED units, and greatly shortens the life span of the lights.
Ergonomic light distribution
The light and color scheme of its products comply with road operators’ visual habits. The products adopt equal-brightness optical design in full consideration that it is unavailable to detect illumination by eyes because human eyes are sensitive to brightness, thus not only eliminating the visual bright spots and dark spots on road surface, but also bringing visual ease and comfort to road operators, as well as improving lighting illumination and obtaining accurate detected values.
It is available to freely equip with different number of modules to achieve different powers as required.
LED Street Light
- Side-entry LED Road Light
- Side-entry & Post-top LED Roadway Light
- LED Garden Light
LED Flood Light
- High Mast Flood Light
- Airport & Harbor & Stadium LED Flood Light
- Wall Mount LED Flood Light
- LED High Bay Light
- LED Tunnel Light
- LED Canopy Light
- LED Horticulture Light
- 3535 SMD LED Module
- 3030 SMD LED Module
- 5050 SMD LED Module